Direct model-based predictive control scheme without cost function for voltage source inverters with reduced common-mode voltage

This paper presents a direct model-based predictive control scheme for voltage source inverters (VSIs) with reduced common-mode voltages (CMVs). The developed method directly finds optimal vectors without using repetitive calculation of a cost function. To adjust output currents with the CMVs in the range of –V_dc/6 to +V_dc/6, the developed method uses voltage vectors, as finite control resources, excluding zero voltage vectors which produce the CMVs in the VSI within ±V_dc/2. In a model-based predictive control (MPC), not using zero voltage vectors increases the output current ripples and the current errors. To alleviate these problems, the developed method uses two non-zero voltage vectors in one sampling step. In addition, the voltage vectors scheduled to be used are directly selected at every sampling step once the developed method calculates the future reference voltage vector, saving the efforts of repeatedly calculating the cost function. And the two non-zero voltage vectors are optimally allocated to make the output current approach the reference current as close as possible. Thus, low CMV, rapid current-following capability and sufficient output current ripple performance are attained by the developed method. The results of a simulation and an experiment verify the effectiveness of the developed method.     

Parallel Multipopulation Differential Evolutionary Particle Swarm Optimization for Voltage and Reactive Power Control

This paper presents parallel multipopulation differential evolutionary particle swarm optimization (DEEPSO) for voltage and reactive power control (VQC). The problem can be formulated as a mixed integer nonlinear optimization problem and various evolutionary computation techniques have been applied to the problem including PSO, differential evolution (DE), and DEEPSO. Since VQC is one of the online controls, speed‐up of computation is required. Moreover, there is still room for improvement in solution quality. This paper applies parallel multipopulation DEEPSO in order to speed up the calculation and improve solution quality. The proposed method is applied to IEEE 30, 57, and 118 bus systems. The results indicate that the proposed method can realize fast computation and minimize more active power losses than the conventional evolutionary computation techniques.     

阳极导电材料对铁钨锡合金粉电解铁的影响

研究阳极导电材料碳素钢、316L不锈钢、铅钙合金、石墨、钛涂钌板、钛板和铜板在硫酸盐和氯盐体系中对铁钨锡合金粉电解铁的影响。结果表明:电解24 h,上述阳极导电材料在氯盐中的阴极电流效率为90%、90%、66%、66%、54%、49%、33%,在硫酸盐中的阴极电流效率为90%、87%、82%、81%、73%、68%、54%。槽电压均逐渐升高,在氯盐体系中,石墨、铅钙合金、钛涂钌板和钛板作阳极导电材料时,电解液pH逐渐降低;碳素钢、316L不锈钢和铜板作阳极导电材料时,电解液pH逐渐升高。在硫酸盐体系中,铜板和碳素钢作阳极导电材料时,电解液pH基本不变;316L不锈钢作阳极导电材料时,pH逐渐升高;铅钙合金、石墨和钛板作阳极导电材料时,pH先升高后降低。基于槽电压、阴极电流效率,选择适宜的电解体系为硫酸盐体系,该体系中适宜的阳极导电材料为铅钙合金。     

Experimental research on temperature rise and electric characteristics of aluminum air battery under open‐circuit condition for new energy vehicle

Due to lack of systematic research on open‐circuit voltage (OCV) and electrolyte temperature rise characteristics of aluminum air battery, in order to explore the influential factors on the OCV and electrolyte temperature rise of aluminum air battery, in this paper, for the first time, we studied the effects of different ambient temperature conditions, different concentrations of NaOH and KOH electrolyte, and pure aluminum and aluminum alloy on the OCV and electrolyte temperature rise of aluminum air battery. Results show that the OCV of aluminum air battery is obviously affected by ambient temperature conditions, electrolyte concentration, and different anode materials. The OCV range is 1.5 to 1.8 V at 0°C under different KOH‐electrolyte concentrations when aluminum alloy is used as anode material; with the increase of ambient temperature, the OCV will rise, and the range is 1.8 to 1.95 V. The working process of aluminum air battery is accompanied by the phenomenon of heat release, and the temperature rise range of electrolyte will not exceed 7°C when aluminum alloy is used as the anode material; however, the highest temperature of the electrolyte can reach 100°C when pure aluminum is used as the negative electrode material. The results of this study will provide theoretical guidance for designing aluminum air batteries and identifying their optimal operating conditions.     

Evaluation of fluctuating voltage topology with fuel cells and supercapacitors for automotive applications

To develop a single‐stage power conversion topology in which energy storage devices can be directly coupled, a fluctuating voltage topology is applied, leading to lower cost and more compactness with the absence of DC/DC converters. This paper investigates such a topology for automotive applications where fuel cells are directly connected to the DC bus of the inverter, resulting in fluctuating voltage across the DC bus. Further, a supercapacitor pack is also introduced to maintain the power capacity and voltage stability. The hybridization principle and practical application of such a topology are then discussed in the time domain and frequency domain. Furthermore, the transient power requirement is decomposed to design the size of fuel cells and supercapacitors. Simulation results from the modeling of the fuel cell‐supercapacitor powertrain demonstrate the feasibility and effectiveness of this topology. The supercapacitors can serve as a low‐pass filter for the fuel cells. In conclusion, the peak power requirement can be successfully achieved because of the lowered system impedance, and the fuel cells only need to supply the average power.     

基于过程免疫力的动态电压恢复器优化配置

优质电力园区以最低成本满足用户对电能质量的特殊需求,成为解决电压暂降问题的新途径,已在国内外开展了广泛的试点应用。针对中国优质电力园区规划缺少经济高效的优化配置方法的实际情况,提出了一种基于过程免疫力的动态电压恢复器优化配置方法。基于工业过程电压暂降免疫力,以满足用户用电需求为目标,以治理设备购置费用最低为约束,采用遗传算法对园区供电质量分级制定动态电压恢复器的优化配置方案,实现工业园区电压暂降治理的经济性。对大型精密温控系统的电压暂降治理装置的优化配置方法进行仿真计算,验证了所提方法的有效性与经济性。     

Recycling spent lead acid batteries into aqueous zinc-ion battery material with ultra-flat voltage platforms

The harmless disposal of lead paste in the spent lead-acid batteries (LABs) remains an enormous challenge in traditional pyrometallurgical recycling. Here, we introduced a hydrometallurgical method for the recycling of the spent LABs’ waste to obtain the β-PbO as a novel zinc ion batteries (ZIBs) active material. The obtained β-PbO exhibits ultra-flat charge/discharge voltage platforms (0.21 mV/(mAh g^?1)) and stable specific capacity. During the charge/discharge, the β-PbO spontaneously triggers the formation of (ZnSO₄)[Zn(OH)₂]₃·5H₂O (ZHS) micro-sheets as a surface passivation layer. Moreover, the ex-situ X-ray spectra reveal that the reversible phase transformation occurs between PbSO₄ and Pb with the assistance of ZHS by adjusting the PH value on the electrode-electrolyte interface. The synergistic two-phase-reaction mechanism generates ultra-flat voltage platforms upon the charge/discharge. This “energy-saving and environment-friendly” recycling route eliminates the major source of emission of pollution particulates/gases compared to the traditional pyrometallurgical recycling, while at the same time replacing energy-consuming and environmentally detrimental processes of synthesis of current ZIBs cathodes.     

Electron injection barrier and energy-level alignment at the Au/PDI8-CN2 interface via current–voltage measurements and ballistic emission microscopy

We probe electron transport across the Au/organic interface based on oriented thin films of the high-performance n-type perylene diimide semiconductor PDI8-CN₂. To this purpose, we prepared organic-on-inorganic Schottky diodes, with Au directly evaporated onto PDI8-CN₂ grown on n-Si. Temperature-dependent current–voltage characteristics and complementary ballistic electron emission microscopy studies reveal that rectification at the Au/PDI8-CN₂ interface is controlled by a spatially inhomogeneous injection barrier, that varies on a length scale of tens of nanometers according to a Gaussian distribution with mean value ∼0.94 eV and standard deviation ∼100 meV. The former gradually shifts to ∼1.04 eV on increasing PDI8-CN₂ thickness from 5 nm to 50 nm. Experimental evidences and general arguments further allow to establish the energetics at the Au/PDI8-CN₂ interface. Our work indicates injection-limited current flow in PDI8-CN₂-based devices with evaporated Au electrodes. Furthermore, it suggests chemical reactivity of PDI8-CN₂ with both Au and Si, driven by the lateral isocyano groups.     

Carbon nanotube–polyaniline composites

The last decade has seen a growing interest in hybrid electrically conducting nanocomposites. This article aims to provide a detailed overview of the present status of research in carbon nanotube–polyaniline (CNT/PANI) composites, from processing to structural and property evaluations. CNT/PANI are synthesized by electrochemical and chemical processing. When chemical methods are used, the main challenge is to obtain processable CNT/PANI in the emeraldine salt (ES) form composites. Stable dispersions of ES–CNT in organic media are prepared using the post doping method, inverse emulsion polymerization, or ex situ polymerizations. On the contrary, stable water dispersions of CNT/ES are prepared using hydrophilization of a preformed CNT/ES composite, direct synthesis of micelle–CNT hybrid templates, interfacial polymerization, covalent functionalization of CNT with a water soluble polymer, or using electrostatic interactions between two oppositely charged ES and CNT aqueous colloids. Moreover, the strategies for the synthesis of ternary CNT/PANI composites incorporating noble metal nanoparticles, metal oxide, or graphene sheets are also presented and analyzed in depth. Finally, we give a review of potential applications, including chemical sensors, capacitors, fuel cells and electronic devices.     

熔体静电纺丝的工艺条件对纺丝纤维直径的影响

主要研究纺丝温度、纺丝电压、接收距离等参数对聚丙烯(PP)熔体静电纺丝纤维直径的影响。采用了只变一个参数,其它参数固定的常规实验方法。在实验条件范围内,随着纺丝温度的升高,纤维的平均直径逐渐减小,得到PP的最佳纺丝温度240℃。在固定电压的情况下,得到最佳接收距离7cm。在固定接收距离的情况下,随着电压的增加,电场中的喷射流熔体受到的电场力逐渐增大,得出最佳纺丝电压35kV。